S-One Essential Airbrush Kit

• Extra fittings may be required for various airbrush brands, models.

STEP 2: Carefully plug the compressor into a standard wall outlet.

STEP 3: Turn the switch on. The compressor will run continuously until you shut it off.

STEP 4: When restarting the compressor during operation, always release the air pressure first and turn on again.

• Work in a ventilated area.
• The motor is thermally protected and automatically shuts off when it becomes overheated. If this occurs, turn the compressor off and wait for it to restart until after it cools.
• Do not use any lubricant, which may damage the air compressor.
• When you restart the compressor during operation, always release the air pressure first, then turn on.

STEP 1: Using airbrush wrench (part 24) or your fingers, place the brass nozzle on the front of the airbrush gun.

STEP 2: Screw on the nozzle to the tip of the airbrush gun until securely tightened.

STEP 3: Screw on the nozzle cap.

STEP 4: Screw on the needle cap.

STEP 5: Hold the airbrush gun in your hand at a 45 degree angle, insert the trigger sideways into the body and twist so the lines face the front of the airbrush body.

STEP 6: With the body at an angle, grasp the needle chucking guide and insert it into the back of the airbrush gun. This action will push the trigger forward.

STEP 7: Slide the spring over the needle chucking guide.

STEP 8: Screw on the spring case, twisting clockwise.

STEP 9: Gently insert the needle.

STEP 10: Screw on the needle chucking nut.

STEP 11: Screw on the handle.

STEP 12: Your SP-35 Airbrush Gun is now assembled!

STEP 1: Attach the airbrush gun to compressor hose using the metal screw-on connector.

STEP 2: Drop makeup into airbrush cup. For use with airbrush foundation, start with 4-6 drops of makeup. For blush, highlighter and other colors, start with 3-4 drops.

STEP 3: Turn on compressor and bring airbrush gun up to 4-6 inches from face.

STEP 4: Begin makeup application. Always start by releasing air first, pressing down on trigger to release air. Next, pull back on trigger to release makeup. Make sure the air is on at all times during application.

STEP 5: Begin airbrush makeup application. Pull back on trigger for makeup control.

STEP 6: Apply airbrush makeup in small circular motions. Keep moving and watch carefully so as not to overspray. It is important to stop periodically and review your work.

STEP 7: Move the airbrush gun 4-6" away from the face as necessary and adjust the dial pressure on the compressor as needed.

• For silicone/oil-based formulas use S/B Airbrush Cleaner
• For alcohol-based formulas use Alcohol 99%
• For water-based formulas use water

STEP 2: Add a few drops of cleaning solution to the cup.

STEP 3: Using a cotton swab or small brush, swish the cleaning solution around the cup.

STEP 4: Spray the solution through the airbrush gun onto a tissue or into the Pro Airbrush Cleaning Pot.

If needed, mix different concealer shades to match your foundation.

Before you apply, mix the concealer and your perfectly matched foundation on the the back of your hand. The mixture will help set the concealer and make the application look as flawless as your skin.

Base Primer: AQUA, ISODO-DECANE, DIMETHICONE, CYCLOPEN-TASILOXANE, BUTYLENE GLYCOL, SILICA, VINYL DIMETHICONE/METHI- CONE SILSESQUIOXANE CROSS- POLYMER, GLYCERIN, DIMETHICONE- /VINYL DIMETHICONE CROSS- POLYMER, PEG/PPG-18/18 DIMETHICONE,CAPRYLIC/CAPRIC TRIGLYCERIDE, CYCLOTETRASI- LOXANE, DISODIUM EDTA, PHENOXYETHANOL

S/B Foundation: Cyclopentasiloxane, Aqua (Water, Eau), Butylene Glycol, Trimethylsiloxysilicate, Alcohol, Leuconostoc/Radish Root Ferment Filtrate, Cyclomethicone, Lactobacillus, PEG/PPG-20/15 Dimethicone, PEG/PPG-18/18 Dimethicone, Polysorbate 80, Sodium Chloride, Polyethylene, Silica, Glyceryl Dibehenate, Tribehenin, Cocos Nucifera (Coconut) Fruit Extract, Glyceryl Behenate, Triethoxycaprylylsilane, Tocopheryl Acetate, Isopropyl Titanium Triisostearate. May Contain: CI 77891, CI 19140, CI 15850, CI 77499, CI 77288, CI 77007

S/B Blush: Cyclopentasiloxane, Aqua (Water, Eau), Butylene Glycol, Trimethylsiloxysilicate, Alcohol, Leuconostoc/Radish Root Ferment Filtrate, PEG/PPG-18/18 Dimethicone, Cyclomethicone, Lactobacillus, PEG/PPG-20/15 Dimethicone, Polysorbate 80, Sodium Chloride, Polyethylene, Silica, Glyceryl Dibehenate, Tribehenin, Cocos Nucifera (Coconut) Fruit Extract, Glyceryl Behenate, Isopropyl Alcohol, Isopropyl Titanium Triisostearate, Triethoxycaprylylsilane, Tocopheryl Acetate. May Contain: CI 77891, CI 19140, CI 15850, CI 77491, CI 77499, CI 77492, CI 42090, CI 77007

S/B Highlighter: Cyclopentasiloxane, Aqua (Water, Eau), Butylene Glycol, Trimethylsiloxysilicate, Alcohol, Mica, Leuconostoc/Radish Root Ferment Filtrate, Cyclomethicone, Lactobacillus, PEG/PPG-20/15 Dimethicone, Polysorbate 80, Sodium Chloride, Polyethylene, Silica, Glyceryl Dibehenate, Tribehenin, Cocos Nucifera (Coconut) Fruit Extract, Glyceryl Behenate, Triethoxycaprylylsilane, Isopropyl Alcohol. May Contain: CI 77491, CI 77891, CI 77492, CI 77499

Concealer Wheel: Propylene Glycol Dicaprylate/Dicaprate, Isopropyl Myristate, Ozokerite, Mineral Oil, Silica, Kaolin, Sorbitan Sesquioleate, Tocopheryl Acetate, Ethylhexyl Hydroxystearate, BHA, Talc. May Contain: CI 77891, CI 77491, CI 77492, CI 77499, CI 77007, CI 15850, CI 19140, CI 77288

Q. Is the S-One capable of 220V usage or 110V exclusively?

A: The S-One is made for 110V usage exclusively. A 220V version is available on special order (contact Customer Care) if the country you are living in or traveling to requires 220V.

Q. Can the S-One be used to do airbrush artwork?

A: Yes - the S-One Compressor has a max range of 40 psi and is compatible with water paint and other paint types that can be used for non-makeup airbrush artistry.

Q. What airbrush gun the S-One Compressor compatible with?

A: The S-One is compatible with an SP-35 or SP-40 Airbrush Gun (sold separately), or the Airpod Pro using the Airpod Airbrush for Pro Plus and S-One Compressors.